Below is a list of water-related terms that may prove helpful while navigating the LEHMUA.Com website. The glossary is compiled from a number of sources and should not be considered an official water glossary. A detailed water glossary is kept by the Water Quality Association, and an extremely detailed water dictionary is offered by the Nevada Division of Water Planning.
Average Monthly Discharge Limitations The highest allowable average of daily discharges over a calendar month, calculated as the sum of all daily discharges measured during that month divided by the number of days on which monitoring was performed (except in the case of fecal coliform). Back to Top
Average Weekly Discharge Limitation The highest allowable average of daily discharges over a calendar week, calculated as the sum of all daily discharges measured during a calendar week divided by the number of daily discharges measured during that week. Back to Top
Best Available Technology Economically Achievable (BAT) Technology-based standard established by the Clean Water Act (CWA) as the most appropriate means available on a national basis for controlling the direct discharge of toxic and nonconventional pollutants to navigable waters. BAT effluent limitations guidelines, in general, represent the best existing performance of treatment technologies that are economically achievable within an industrial point source category or subcategory Back to Top
Best Conventional Pollutant Control Technology (BCT) Technology-based standard for the discharge from existing industrial point sources of conventional pollutants including BOD, TSS, fecal coliform, pH, oil and grease. The BCT is established in light of a two-part "cost reasonableness" test which compares the cost for an industry to reduce its pollutant discharge with the cost to a POTW for similar levels of reduction of a pollutant loading. The second test examines the cost-effectiveness of additional industrial treatment beyond BPT. EPA must find limits which are reasonable under both tests before establishing them as BCT. Back to Top
Best Management Practice (BMP) Permit condition used in place of or in conjunction with effluent limitations to prevent or control the discharge of pollutants. May include schedule of activities, prohibition of practices, maintenance procedure, or other management practice. BMPs may include, but are not limited to, treatment requirements, operating procedures, or practices to control plant site runoff, spillage, leaks, sludge or waste disposal, or drainage from raw material storage. Back to Top
Biochemical Oxygen Demand (BOD) A measurement of the amount of oxygen utilized by the decomposition of organic material, over a specified time period (usually 5 days) in a wastewater sample; it is used as a measurement of the readily decomposable organic content of a wastewater. Back to Top
Categorical Industrial User (CIU) An industrial user subject to national categorical pretreatment standards. Back to Top
Categorical Pretreatment Standards Limitations on pollutant discharges to publicly owned treatment works promulgated by EPA in accordance with Section 307 of the Clean Water Act that apply to specified process wastewaters of particular industrial categories [40 CFR 403.6 and Parts 405-471].vv Back to Top
Chemical Oxygen Demand (COD) A measure of the oxygen-consuming capacity of inorganic and organic matter present in wastewater. COD is expressed as the amount of oxygen consumed in mg/l. Results do not necessarily correlate to the biochemical oxygen demand (BOD) because the chemical oxidant may react with substances that bacteria do not stabilize. Back to Top
Clean Water Act (CWA) The Clean Water Act is an act passed by the U.S. Congress to control water pollution. It was formerly referred to as the Federal Water Pollution Control Act of 1972 or Federal Water Pollution Control Act Amendments of 1972 (Public Law 92-500), 33 U.S.C. 1251 et. seq., as amended by: Public Law 96-483; Public Law 97-117; Public Laws 95-217, 97-117, 97-440, and 100-04. Clean Water Act (CWA) The Clean Water Act is an act passed by the U.S. Congress to control water pollution. It was formerly referred to as the Federal Water Pollution Control Act of 1972 or Federal Water Pollution Control Act Amendments of 1972 (Public Law 92-500), 33 U.S.C. 1251 et. seq., as amended by: Public Law 96-483; Public Law 97-117; Public Laws 95-217, 97-117, 97-440, and 100-04. Back to Top
Combined Sewer Overflow (CSO) A discharge of untreated wastewater from a combined sewer system at a point prior to the headworks of a publicly owned treatment works. CSOs generally occur during wet weather (rainfall or snowmelt). During periods of wet weather, these systems become overloaded, bypass treatment works, and discharge directly to receiving waters. Back to Top
Combined Sewer System (CSS) A wastewater collection system which conveys sanitary wastewaters (domestic, commercial and industrial wastewaters) and storm water through a single pipe to a publicly owned treatment works for treatment prior to discharge to surface waters. Back to Top
Compliance The act of meeting all state and federal drinking water regulations. Back to Top
Compliance Schedule A schedule of remedial measures included in a permit or an enforcement order, including a sequence of interim requirements (for example, actions, operations, or milestone events) that lead to compliance with the CWA and regulations. Back to Top
Composite Sample Sample composed of two or more discrete samples. The aggregate sample will reflect the average water quality covering the compositing or sample period. Back to Top
Contaminant Anything found in water (including microorganisms, minerals, chemicals, radionuclides, etc.) which may be harmful to human health. Back to Top
Conventional Pollutants Pollutants typical of municipal sewage, and for which municipal secondary treatment plants are typically designed; defined by Federal Regulation [40 CFR 401.16] as BOD, TSS, fecal coliform bacteria, oil and grease, and pH. Back to Top
Cryptosporidium A microorganism commonly found in lakes and rivers which is highly resistant to disinfection. Cryptosporidium has caused several large outbreaks of gastrointestinal illness, with symptoms that include diarrhea, nausea, and/or stomach cramps. People with severely weakened immune systems (that is, severely immuno-compromised) are likely to have more severe and more persistent symptoms than healthy individuals. Back to Top
Daily Discharge The discharge of a pollutant measured during any 24-hour period that reasonably represents a calendar day for purposes of sampling. For pollutants with limitations expressed in units of mass, the daily discharge is calculated as the total mass of the pollutant discharged during the day. For pollutants with limitations expressed in other units of measurement (e.g., concentration) the daily discharge is calculated as the average measurement of the pollutant throughout the day (40 CFR 122.2). Back to Top
Daily Maximum Limit The maximum allowable discharge of pollutant during a calendar day. Where daily maximum limitations are expressed in units of mass, the daily discharge is the total mass discharged over the course of the day. Where daily maximum limitations are expressed in terms of a concentration, the daily discharge is the arithmetic average measurement of the pollutant concentration derived from all measurements taken that day. Back to Top
Discharge Monitoring Report (DMR) The form used (including any subsequent additions, revisions, or modifications) to report self-monitoring results by NPDES permittees. DMRs must be used by approved states as well as by EPA. Back to Top
Disinfectant A chemical (commonly chlorine, chloramine, or ozone) or physical process (e.g., ultraviolet light) that kills microorganisms such as bacteria, viruses, and protozoa. Back to Top
Distribution System A network of pipes leading from a treatment plant to customers' plumbing systems. Back to Top
Draft Permit A document prepared under 40 CFR 124.6 indicating the Director's tentative decision to issue, deny, modify, revoke and reissue, terminate, or reissue a permit. A notice of intent to terminate a permit, and a notice of intent to deny a permit application, as discussed in 40 CFR 124.5, are considered draft permits. A denial of a request for modification, revocation and reissuance, or termination, as discussed in 40 CFR 124.5, is not a draft permit. Back to Top
Effluent Limitation Any restriction imposed by the Director on quantities, discharge rates, and concentrations of pollutants which are discharged from point sources into waters of the United States, the waters of the contiguous zone, or the ocean. Back to Top
Effluent Limitations Guidelines (ELG) A regulation published by the Administrator under Section 304(b) of CWA that establishes national technology-based effluent requirements for a specific industrial category. Back to Top
Exemption State or EPA permission for a water system not to meet a certain drinking water standard. An exemption allows a system additional time to obtain financial assistance or make improvements in order to come into compliance with the standard. The system must prove that: (1) there are compelling reasons (including economic factors) why it cannot meet a MCL or Treatment Technique; (2) it was in operation on the effective date of the requirement, and (3) the exemption will not create an unreasonable risk to public health. The state must set a schedule under which the water system will comply with the standard for which it received an exemption. Back to Top
Fact Sheet A document that must be prepared for all draft individual permits for NPDES major dischargers, NPDES general permits, NPDES permits that contain variances, NPDES permits that contain sewage sludge land application plans and several other classes of permittees. The document summarizes the principal facts and the significant factual, legal, methodological and policy questions considered in preparing the draft permit and tells how the public may comment (40 CFR 124.8 and 124.56). Where a fact sheet is not required, a statement of basis must be prepared (40 CFR 124.7). Back to Top
Finished Water Water that has been treated and is ready to be delivered to customers. Back to Top
Giardia lamblia A microorganism frequently found in rivers and lakes, which, if not treated properly, may cause diarrhea, fatigue, and cramps after ingestion. Back to Top
Ground Water The water that systems pump and treat from aquifers (natural reservoirs below the earth's surface). Back to Top
Hazars douSubstance Any substance, other than oil, which, when discharged in any quantities into waters of the U.S., presents an imminent and substantial danger to the public health or welfare, including but not limited to fish, shellfish, wildlife, shorelines and beaches (Section 311 of the CWA); identified by EPA as the pollutants listed under 40 CFR Part 116. Any substance, other than oil, which, when discharged in any quantities into waters of the U.S., presents an imminent and substantial danger to the public health or welfare, including but not limited to fish, shellfish, wildlife, shorelines and beaches (Section 311 of the CWA); identified by EPA as the pollutants listed under 40 CFR Part 116. Back to Top
Health Advisory An EPA document that provides guidance and information on contaminants that can affect human health and that may occur in drinking water, but which EPA does not currently regulate in drinking water. Back to Top
Indirect Discharge The introduction of pollutants into a municipal sewage treatment system from any nondomestic source (i.e., any industrial or commercial facility) regulated under Section 307(b), (c), or (d) of the CWA. Back to Top
Inorganic Contaminants Mineral-based compounds such as metals, nitrates, and asbestos. These contaminants are naturally-occurring in some water, but can also get into water through farming, chemical manufacturing, and other human activities. EPA has set legal limits on 15 inorganic contaminants. Back to Top
Junk Junk is what is left over after you take away the good stuff. Back to Top
Junk Junk is what is left over after you take away the good stuff. Back to Top
Local Limits Conditional discharge limits imposed by municipalities upon industrial or commercial facilities that discharge to the municipal sewage treatment system. Back to Top
Maximum Contaminant Level (MCL) The highest level of a contaminant that EPA allows in drinking water. MCLs ensure that drinking water does not pose either a short-term or long-term health risk. EPA sets MCLs at levels that are economically and technologically feasible. Some states set MCLs which are more strict than EPA's. Back to Top
Maximum Contaminant Level Goal (MCLG) The level of a contaminant at which there would be no risk to human health. This goal is not always economically or technologically feasible, and the goal is not legally enforceable. Back to Top
Method Detection Limit (MDL) Defined as the minimum concentration of a substance that can be measured and reported with 99 percent confidence that the analyte concentration is greater than zero and is determined from analysis of a sample in a given matrix containing the analyte. Back to Top
Microorganisms Tiny living organisms that can be seen only with the aid of a microscope. Some microorganisms can cause acute health problems when consumed in drinking water. Also known as microbes. Back to Top
Microorganisms Tiny living organisms that can be seen only with the aid of a microscope. Some microorganisms can cause acute health problems when consumed in drinking water. Also known as microbes. Back to Top
Million Gallons per Day (mgd) A unit of flow commonly used for wastewater discharges. One mgd is equivalent to 1.547 cubic feet per second. Back to Top
Monitoring Testing that water systems must perform to detect and measure contaminants. A water system that does not follow EPA's monitoring methodology or schedule is in violation, and may be subject to legal action. Back to Top
Municipal Separate Storm Sewer System (MS4) A conveyance or system of conveyances (including roads with drainage systems, municipal streets, catch basins, curbs, gutters, ditches, manmade channels, or storm drains) owned by a state, city, town or other public body, that is designed or used for collecting or conveying storm water, which is not a combined sewer, and which is not part of a publicly owned treatment works. Commonly referred to as an "MS4" [40 CFR 122.26(b)(8)]. Back to Top
National Pollutant Discharge Elimination System (NPDES) National Pollutant Discharge Elimination System (NPDES) The national program for issuing, modifying, revoking and reissuing, terminating, monitoring and enforcing permits, and imposing and enforcing pretreatment requirements, under Sections 307, 318, 402, and 405 of CWA. Back to Top
National Pretreatment Standard or Pretreatment Standard Any regulation promulgated by the EPA in accordance with Sections 307(b) and (c) of the CWA that applies to a specific category of industrial users and provides limitations on the introduction of pollutants into publicly owned treatment works. This term includes the prohibited discharge standards under 40 CFR 403.5, including local limits [40 CFR 403.3(j)]. Back to Top
New Source Any building, structure, facility, or installation from which there is or may be a discharge of pollutants, the construction of which commenced: a. After promulgation of standards of performance under Section 306 of the CWA which are applicable to such source; or b. After proposal of standards of performance in accordance with Section 306 of the CWA which are applicable to such source, but only if the standards are promulgated in accordance with Section 306 of the CWA within 120 days of their proposal. c. Except as otherwise provided in an applicable new source performance standard, a source is a new source if it meets the definition in 40 CFR 122.2; and i. It is constructed at a site at which no other source is located; or ii. It totally replaces the process or production equipment that causes the discharge of pollutants at an existing source; or iii. Its processes are substantially independent of an existing source at the same site. In determining whether these processes are substantially independent, the Director shall consider such factors as the extent to which the new facility is integrated with the existing plant; and the extent to which the new facility is engaged in the same general type of activity as the existing source. Back to Top
New Source Performance Standards (NSPS) Technology-based standards for facilities that qualify as new sources under 40 CFR 122.2 and 40 CFR 122.29. Standards consider that the new source facility has an opportunity to design operations to more effectively control pollutant discharges. Back to Top
Nonconventional Pollutants All pollutants that are not included in the list of conventional or toxic pollutants in 40 CFR Part 401. Includes pollutants such as chemical oxygen demand (COD), total organic carbon (TOC), nitrogen, and phosphorus. Back to Top
pH A measure of the hydrogen ion concentration of water or wastewater; expressed as the negative log of the hydrogen ion concentration in mg/l. A pH of 7 is neutral. A pH less than 7 is acidic, and a pH greater than 7 is basic.pH A measure of the hydrogen ion concentration of water or wastewater; expressed as the negative log of the hydrogen ion concentration in mg/l. A pH of 7 is neutral. A pH less than 7 is acidic, and a pH greater than 7 is basic.v Back to Top
Point Source xAny discernible, confined, and discrete conveyance, including but not limited to any pipe, ditch, channel, tunnel, conduit, well, discrete fixture, container, rolling stock, concentrated animal feeding operation, landfill leachate collection system, vessel, or other floating craft from which pollutants are or may be discharged. Back to Top
Pollutant Dredged spoil, solid waste, incinerator residue, filter backwash, sewage, garbage, sewage sludge, munitions, chemical wastes, biological materials, radioactive materials (except those regulated under the Atomic Energy Act of 1954, as amended (42 U.S.C. 2011 et seq.)), heat, wrecked or discarded equipment, rock, sand, cellar dirt and industrial, municipal, and agricultural waste discharged into water. Back to Top
Practical Quantification Limit (PQL) The lowest level that can be reliably achieved within specified limits of precision and accuracy during routine laboratory operating conditions. Back to Top
Pretreatment The reduction of the amount of pollutants, the elimination of pollutants, or the alteration of the nature of pollutant properties in wastewater prior to or in lieu of discharging or otherwise introducing such pollutants into a publicly owned treatment works [40 CFR 403.3(q)]. Back to Top
Primary Treatment The practice of removing some portion of the suspended solids and organic matter in a wastewater through sedimentation. Common usage of this term also includes preliminary treatment to remove wastewater constituents that may cause maintenance or operational problems in the system (i.e., grit removal, screening for rags and debris, oil and grease removal, etc.). Back to Top
Priority Pollutants Those pollutants considered to be of principal importance for control under the CWA based on the NRDC consent decree settlement [( NRDC et al. v. Train, 8 E.R.C. 2120 (D.D.C. 1976), modified 12 E.R.C. 1833 (D.D.C. 1979)]; a list of these pollutants is provided as Appendix A to 40 CFR Part 423. Back to Top
Process Wastewater Any water which, during manufacturing or processing, comes into direct contact with, or results from the production or use of any raw material, intermediate product, finished product, byproduct, or waste product. Back to Top
Production-Based Standard A discharge standard expressed in terms of pollutant mass allowed in a discharge per unit of product manufactured. Back to Top
Proposed Permit A state NPDES permit prepared after the close of the public comment period (and when applicable, any public hearing and administrative appeals) which is sent to EPA for review before final issuance by the state. Back to Top
Publicly Owned Treatment Works (POTW) A treatment works, as defined by Section 212 of the CWA, that is owned by the state or municipality. This definition includes any devices and systems used in the storage, treatment, recycling, and reclamation of municipal sewage or industrial wastes of a liquid nature. It also includes sewers, pipes, and other conveyances only if they convey wastewater to a POTW treatment plant [40 CFR 403.3]. Back to Top
Sanitary Sewer A pipe or conduit (sewer) intended to carry wastewater or water-borne wastes from homes, businesses, and industries to the POTW. Back to Top
Sanitary Sewer Overflows (SSO) Untreated or partially treated sewage overflows from a sanitary sewer collection system. Back to Top
Secondary Treatment Technology-based requirements for direct discharging municipal sewage treatment facilities. Standard is based on a combination of physical and biological processes typical for the treatment of pollutants in municipal sewage. Standards are expressed as a minimum level of effluent quality in terms of: BOD 5 , suspended solids (SS), and pH (except as provided for special considerations and treatment equivalent to secondary treatment). Back to Top
Self-Monitoring Sampling and analyses performed by a facility to determine compliance with a permit or other regulatory requirements. Back to Top
Spill Prevention Control and Countermeasure Plan (SPCC) A plan prepared by a facility to minimize the likelihood of a spill and to expedite control and cleanup activities should a spill occur. Back to Top
Storm Water Storm water runoff, snow melt runoff, and surface runoff and drainage [40 CFR 122.26(b)(13)]. Back to Top
Total Maximum Daily Load (TMDL) The amount of pollutant, or property of a pollutant, from point, nonpoint, and natural background sources, that may be discharged to a water quality-limited receiving water. Any pollutant loading above the TMDL results in violation of applicable water quality standards. Back to Top
Total Organic Carbon (TOC) Measures the amount of organic carbon in water. Back to Top
Total Suspended Solids (TSS) A measure of the filterable solids present in a sample, as determined by the method specified in 40 CFR Part 136. Back to Top
Toxic Pollutant Pollutants or combinations of pollutants, including disease-causing agents, which after discharge and upon exposure, ingestion, inhalation or assimilation into any organism, either directly from the environment or indirectly by ingestion through food chains, will, on the basis of information available to the Administrator of EPA, cause death, disease, behavioral abnormalities, cancer, genetic mutations, physiological malfunctions, (including malfunctions in reproduction) or physical deformations, in such organisms or their offspring. Toxic pollutants also include those pollutants listed by the Administrator under CWA Section 307(a)(1) or any pollutant listed under Section 405(d) which relates to sludge management. Back to Top
Toxicity Reduction Evaluation (TRE) A site-specific study conducted in a stepwise process designed to identify the causative agent(s) of effluent toxicity, isolate the sources of toxicity, evaluate the effectiveness of toxicity control options, and then confirm the reduction in effluent toxicity. Back to Top
Toxicity Test A procedure to determine the toxicity of a chemical or an effluent using living organisms. A toxicity test measures the degree of effect on exposed test organisms of a specific chemical or effluent. Back to Top
Variance Any mechanism or provision under Sections 301 or 316 of the CWA or under 40 CFR Part 125, or in the applicable "effluent limitations guidelines" which allows modification to or waiver of the generally applicable effluent limitations requirements or time deadlines of the CWA. This includes provisions which allow the establishment of alternative limitations based on fundamentally different factors. Back to Top
Water Quality Criteria Comprised of numeric and narrative criteria. Numeric criteria are scientifically derived ambient concentrations developed by EPA or states for various pollutants of concern to protect human health and aquatic life. Narrative criteria are statements that describe the desired water quality goal. Back to Top
Water Quality Standard (WQS) A law or regulation that consists of the beneficial use or uses of a waterbody, the numeric and narrative water quality criteria that are necessary to protect the use or uses of that particular waterbody, and an antidegradation statement. Back to Top
Water Quality-Based Effluent Limit (WQBEL) A value determined by selecting the most stringent of the effluent limits calculated using all applicable water quality criteria (e.g., aquatic life, human health, and wildlife) for a specific point source to a specific receiving water for a given pollutant. Back to Top
Waters of the United States All waters that are currently used, were used in the past, or may be susceptible to use in interstate or foreign commerce, including all waters subject to the ebb and flow of the tide. Waters of the United States include but are not limited to all interstate waters and intrastate lakes, rivers, streams (including intermittent streams), mudflats, sand flats, wetlands, sloughs, prairie potholes, wet meadows, play lakes, or natural ponds. [See 40 CFR 122.2 for the complete definition.] Back to Top